L. A. Ornamental & Rack Corp 3708 NW 82nd Street Miami, Florida 33147 Office: 305-696-0419 Fax: 305-696-0461 |
About Us | Contact Us | Our Policies | FAQ | Manufactures | Links | Copyright Protected 2004-2008 - L. A. Ornamental & Rack Corp. All rights reserved. No part of this site can be reproduced in any form or by any means, electronic, mechanical, photocopying, or otherwise without prior written consent of L. A. Ornamental & Rack Corp. 3708 NW 82nd Street Miami Florida 33147, Office: 305-696-0419 Fax: 305-696-0461 E-Mail: LAOrnamental@Aol.com |
BD Loops |
Preformed 3/16” Saw-cut Loop Used for saw-cut installations where a 3/16” groove is cut into the concrete or asphalt and the wire is stuffed and sealed (using loop sealent) into the surface. Our saw-cut loops have a custom polyethylene outer jacket protects a micro-dusted nylon coated inner jacketed 16AWG stranded wire. The saw-cut loop has a built in backer-rod securely fitting a 3/16” saw-cut groove eliminating the need to apply backer-rod to hold the loop to the bottom of the saw-cut groove and requires 30-40% less loop sealant to seal the groove. The entire loop including the lead-in fits within a 3/16” saw-cut groove preventing wasted time spent double saw-cutting or doubling blades to cut the home run lead-in. •Works best with 3/16" saw-cut blade or wider. (Does not work with 1/8" blade.) •Can be used with 1/4" blade. •Use the TB-Kit to ensure the groove is cut exactly every time. •Loop should only be installed black side up to ensure phasing direction matches. •Align loop over saw-cut groove before insertion into the groove will prevent having to pull up and realign a “tight- fitting” loop. •Loops are not normally seen by your customers, if one doesn’t work its likely other parts/work will be blamed. BD Loops has the best performance track record in the industry - insuring the quality of your work. •All loops are made with 14 & 16AWG two to three times at much copper per foot vs. 18AWG. •Will save you 15-30min per loop in installation time vs. wrapping your own. •9 years of business 200,000 loops installed and only 1 loop failure. •Designed to save installers 15-30min per loop. By installing 3 loops, installers can cut one and a half hours of labor costs; worth close to $150. •The savings pay for the cost of the loops. •A better quality product. |
Pre-Form Saw Loops |
|
EMX Loop Detectors |
|
Direct Burial Preform Loops |
Preformed Direct Burial Loops Used for installations under concrete, asphalt, pavers, or gravel roads. The most common installation is the loop tied directly to the rebar before concrete is poured. Wire is UL 493 certified designed for a direct burial application. Unlike loops wrapped through PVC, The BD Loops Direct Burial Loop does not have an air pocket resulting in fewer repeat service calls due to phantom detections caused by ground vibration. Built with a high quality solid 14AWG wire out performing other preformed loops with twice as much copper per foot and increased tensile strength. Solid 14AWG wire also results in the direct burial loop being very ridged giving the installer the opportunity to easily set-up and layout the loop and prevents the loop from falling in- between the rebar patter. Twisted jacketed lead-in prevents “coil back” from normal twisted lead-in, preventing wasted time untangling lead-in wires. The loop wire has arrows indicating the direction of current allowing easy understanding of phasing. Each direct burial loop comes with an installation kit including easy to understand instructions, cable ties for installation on top of rebar, ground stakes for under gravel roads, and stickers for easy identification after the loops have been installed. Recommended installation tips: •Offset the direct burial loop from the rebar pattern. •Run lead-in through conduit. •Residential applications recommend a 4’ short leg of the loop. •Commercial application recommend a 6’ short leg of the loop. |
|
Direct Burial Preform Loops |
Diablo Loop Detectors |
EDI Loop Detectors |
Reno Loop Detectors |
EMX Loop Detectors |
Preform Loops |
BD Loop Preformed Saw Cut Loops |